museumliner.blogg.se

Xmos xscope
Xmos xscope








xmos xscope

Looking in we see that we might have trouble picking up 25M_STAR, 25M_TRI and SLI_RST_N that on the xCORE-200 sliceKIT are connected to a tile 0 sub circuit, and not to any pin that would available on the xCORE-200 explorerKIT. 3.3V was already shown as P, but I made it look the same. (Press picture for a PDF):įig.3 – XMOS slice I/O with examples from xCORE-200 sliceKIT, startKIT and WiFi sliceCARD (press for PDF) It’s seen below (press on it to get a PDF to print out, cut and glue in place but screen layout is here). The hardware manual doesn’t tell where the 5V power-good LED is. I made a new label for the top so that it’s available when the board is quite fastened in my fixture

  • The MAC address is on a label at the bottom.
  • So I found some from my pile of different kinds that I have not ditched over the years eXplorerKIT sadly isn’t shipped in a nice foam like the startKIT. I could glue it with my standard contact adhesive (or double sided tape that it came glued with) – and nicely cut it with my FET table saw. So I guess it’s ok to mount them in something I think is polystyrene foam, even it was flammable when I tested it.

    xmos xscope

    Besides, the four plastic mounting pieces do add some air. They would be low-temp and little to be afraid of. There are some capacitors and low-power resistors underneath.

  • Most of the components are on the top.
  • The xTAG3 1V2 (that comes in the box) doesn’t seem to add anything to the idle current consumption.
  • This is purely a ref for you, like all other refs here) Update: After this I discovered USB power meters at Adafruit like USB Charger Doctor – In-line Voltage and Current Meter or USB Voltage Meter with OLED Display.
  • Idle current consumption as it comes out of the box USB 5V is about 75 mA (→375 mW). Measured with no code and when not connected to xTIMEcomposer.
  • Older 1A Apple iPhone USB power adaptors seen Notes 1: Some detail Introįig.1 – XMOS xCORE-200 eXplorerKIT idle current measurement. Also, my non-association with XMOS, see here. Standard disclaimer, this is just for fun. You may even want have a glimpse first at Notes 5: WiFi sliceCARD with TI CC3000 is doomed – if you are here for the WiFi part. Please study the whole table of context first, that may save you a lot of time if you are looking for something special. Then export from that box will be done over the RJ45 RGMII Ethernet connection, from an embedded web server. Such an RFM69 board is then also used in my xCORE-200 eXplorerKIT box that picks up those data. See this described in My aquarium’s data radioed through the shelf. For exporting data from the aquarium box I ended up with an RFM69 radio board that sends in the 433 MHz band. However, I dropped WiFi in all aspects of it. This note has ended up with more than “WiFi” since I also have included the XMOS general Embedded webserver library. It turned out to become an XMOS embedded WiFi blog note. I purchased two of these boards in the summer of 2017. This page is in group Technology (plus My XMOS pages) where I will try to add matters about my XMOS xCORE-200 eXplorerKITs that I haven’t found elsewhere.
  • 8.5 MikroElectronica does ESP8266 and CC3100 based WiFi modules.
  • 8.3 TI CC3200 IoT WiFi has theirs and yours in one chip.
  • 8.2 Adafruit does a Cloud thermometer server.
  • 8.1.1 Hands on the Adafruit ATWINC1500 board for eXplorerKIT or startKIT?.
  • 7 Notes 5: WiFi sliceCARD with TI CC3000 is doomed.
  • 5.17.1 Adafruit done that with the TI CC3000MOD module.
  • 5.16.3 TI: HCI command by function like SimpleLink_Init_Start.
  • 5.16.2 XMOS: HCI commands from TCP tag like HCI_CMND_SIMPLE_LINK_START.
  • 5.14 Screen recording to see how Hello World! feels.
  • 5.13 Hello World! works, but it takes long time to finish (2).
  • 5.12 Atomic, thread safe version timed printf.
  • 5.11 Adding a get_time_now function to use with c files.
  • 5.9 Hello World! works, but it takes long time to finish (1).
  • 5.8.1 XCore Exchange “Loading SPI_CLK is no good”.
  • 5.5 WELCOME TO THE SIMPLE WEBSERVER DEMO worked!.
  • 5.4 Importing sources from another directory.
  • 5.2.1 SPI_MO->SPI_DI, SPI_CLK, SPI_DO->SPI_MI, SPI_CS, SPI_EN, SPI_IRQ defines.
  • 5.1 XCore: Connecting a WiFi sliceCARD to xCORE-200 eXplorerKIT?.
  • 5 Notes 3: WiFi sliceCARD via PCIe/GPIO?.









  • Xmos xscope